 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SCA3000-E05 Data Sheet SCA3000-E05 3-AXIS ULTRA LOW POWER ACCELEROMETER WITH DIGITAL SPI INTERFACE Features * * * * * * 2.35 V - 3.6 V supply voltage, 1.7 - 3.6 V digital I/O voltage 18 g measurement range SPI digital interface Selectable frequency response Ultra low power consumption (2.5 V, 120 A typ) 64 samples/axis buffer memory for output acceleration data and advanced features enable significant power and resource savings at system level Interrupt signal triggered by motion Size 7x7x1.8 mm Proven capacitive 3D-MEMS technology High shock durability RoHS compliant / lead free soldering Applications SCA3000-E05 is targeted to battery operated wrist and hand-held devices. Typical applications are but not limited * Sports equipment * * * * * C/V Analog calibration & ADC DEMUX 1:3 Low-pass Filter Low-pass Filter Low-pass Filter Decimation Decimation Coordinate Mapping and Calibration SCK SPI i/f MISO MOSI CSB Decimation Oscillator & clock Reference Non-Volatile Memory Motion detector Free fall detector Ring Buffer Control & INT INT Figure 1 SCA3000-E05 Block Diagram VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8269100A 1/4 Rev.A SCA3000-E05 Performance Characteristics 1) Parameter Analog and digital Vdd Digital I/O Vdd Operating temperature ** Current consumption * Condition Typical supply range 2.35 - 2.7 V Min Typ 2) Max 2.35 1.7 -40 -18 -300 -5 45 7 50 160 40 320 2.5 1.8 / 2.5 <7 120 120 3.0 160 0.015 3 4 60 9 75 50 22 65 200 50 400 30 200 20 35 325 240 60 480 2.7 2.7 85 Extended supply range 2.7 - 3.6 V Min Typ 2) Max -40 3.3 3.3 <9 150 150 18 500 3.0 160 5 0.015 3 4 60 9 70 50 22 65 200 45 400 30 200 20 85 35 325 Units V V C A A A g mg mg/C Count/g % %/C % FS % Hz Hz Hz mg RMS mg RMS mg RMS Hz Hz Hz ms ms ms pF kHz Vdd Digital I/O Vdd Reset 3) Active Motion Detection mode Nominal Z-axis +1g position -40 ... +85 C -40 ... +85 C Acceleration range * 4) Offset calibration error * Offset temperature error ** 5) Sensitivity * 6) Sensitivity calibration error * Sensitivity temperature error ** 7) Non-Linearity ** 8) Cross-Axis sensitivity ** 9) 10) Bandwidth ** 18 300 +5 Noise ** 11) Output data rate ** Turn on time ** 12) Measurement mode Narrow band measurement mode Wide band measurement mode Measurement mode Narrow band measurement mode Wide band measurement mode Measurement mode Narrow band measurement mode Wide band measurement mode Measurement mode Narrow band measurement mode Wide band measurement mode 75 11 100 Output load ** SPI clock rate ** * ** 1) 2) 3) 4) 5) 6) 7) 8) 9) 100% tested in production Qualified during product validation The product is factory calibrated at 2.5 V in room temperature. Typical values are not guaranteed. Includes the current through the internal 400 k pull-up resistor connected to digital I/O Vdd. Range defined as x 2+ y 2+ z 2 18g . The measuring range is tested on sensing element level. FS = 18g. Offset temperature error = {Count(0g)-Offset} / Sensitivity [ g ]. Sensitivity = Calibrated sensitivity. Offset= Calibrated offset. Sensitivity = {Count(+1g) - Count(-1g)}/2 [Count/g]. Sensitivity temperature error = {[Count(+1g)-Count(-1g)]/2 - Sensitivity} / Sensitivity x 100% [%]. Sensitivity = Calibrated sensitivity. From straight line through sensitivity calibration (+1g, -1g) points. The cross-axis sensitivity determines how much acceleration, perpendicular to the measuring axis, couples to the output. The total cross-axis sensitivity is the geometric sum of the sensitivities of the two axes which are perpendicular to the measuring axis. The angular alignment error between X, Y and Z axis is included into the cross axis sensitivity. Frequency responses according to Figure 3, Figure 4 and Figure 5. 10) VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8269100A 2/4 Rev.A SCA3000-E05 11) Average noise/axis over the measurement bandwidth defined as 1 (n 2 + n 2 + n 2 ) , where nx, ny and nz are y z 3x the measured signal's standard deviation due to noise in x, y and z directions. Settling error less than 1% of FS. 12) Z X Y Figure 2 Sensing directions and package dimensions in mm with 50 m tolerance. Figure 3 Frequency response of SCA3000-E05 in measurement mode Figure 4 Frequency response of SCA3000-E05 in narrow band measurement mode Figure 5 Frequency response of SCA3000-E05 in wide band measurement mode VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8269100A 3/4 Rev.A SCA3000-E05 Figure 6 Application schematic Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Name NC XRESET INT CLK DVSS DVDD DVIO CSB NC NC SCK_SCL MISO_SDA MOSI AVDD AVSS AVSS ATSTIO NC Function Not connected External reset, active low Interrupt output Digital ground Digital ground Digital supply Digital I/O supply Chip select Not connected Not connected SPI serial clock (SCK) SPI data out (MISO) SPI data in (MOSI) Analog supply Analog ground Analog ground Not connected Not connected Table 1 Pin descriptions Document Change Control Rev. 0.1 0.2 0.3 A Date 11-Aug-06 26-Oct-06 04-Jan-07 08-Feb-07 Change Description First version Frequency responses updated Offset and sensitivity temperature dependencies updated. Turn-on time and noise characteristics added. 1st official release VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8269100A 4/4 Rev.A |
Price & Availability of SCA3000-E05
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |